Capacitive sensors supply high accuracy at a relatively low cost. But system designers attempting to use them have been forced to first convert the capacitance to a voltage, then convert the voltage into the digital domain using a precision analog-to-digital converter (ADC). The complex circuit design, lengthy prototype evaluation, and demanding system test usually cause the designer to look for a different sensor. They often select one that's more expensive, less accurate, or both.
While many applications use capacitive sensors, multiple options exist when interfacing to them, which leads to problems with the signal-conditioning circuitry. However, a new approach employs an industry-standard sigma-delta modulator, traditionally used in high-resolution ADCs, that's modified to measure capacitance directly. Before anything, though, it's important to understand where capacitive sensors are used.
Capacitive sensors exhibit a change in capacitance in response to a change in physical stimulus. Used in many areas of industry, their range of applications is astounding, going from the very high-performance end-including industrial, medical, and manufacturing equipment-to the low-performance end, such as key-touch applications. Common examples consist of humidity, pressure, and position sensors. On a broader scale, applications include non-touch switch technology, proximity sensing, fingerprinting, liquid-level measurement, materials property, oil quality, and all kinds of motion sensors.
Interfacing Capacitive Sensors
Traditionally, the challenge for system designers attempting to use capacitive sensors has been to implement a high-performance, low-cost, capacitive-input front-end. In general, measurements are executed by applying an excitation source to the capacitor electrodes. The variation in capacitance is then turned into a variation in voltage, current, frequency, or pulse width. There are several typical methods of capacitance measurement:
A "direct" method charges the capacitor from a defined current source for a known time, then measures the voltage across the capacitor. This method requires a very low current, high-precision current source, and a high-impedance input to measure the voltage.
A second method uses the capacitor to create an RC oscillator, and then measures the time constant, frequency, or period. This method is simple, but it usually doesn't achieve high accuracy.
Another method involves measuring the capacitor's ac impedance. A sine-wave source excites the capacitance, and the capacitor's current and voltage are measured. Using a four-wire ratiometric connection to the capacitor, a synchronous demodulator then provides one of the most accurate results available. However, the circuit is very complex and has the highest part count.
The most common method for interfacing to precision low-capacitance sensors is using a charge amplifier that converts the ratio of the sensor capacitor to a reference capacitor into a voltage (Fig. 1). This circuit can be found integrated into an ASIC in some high-volume applications.
In all of these methods, the capacitance is first converted to a voltage, which is then converted to digital by a precision analog-to-digital converter (ADC). A digital output is used in most applications, but there's an advantage in digitizing the information even if the required sensor output is an analog signal-either a voltage or an industrial-standard 4 to 20 mA. That's because sensor linearization, temperature compensation, and system calibration are much easier to implement in the digital domain than in the analog domain.
A very important aspect in any precision capacitive-sensor application is the way the sensor is connected to the rest of the circuit. Space at the sensor site is often restricted, so the signal-conditioning circuit must be small enough to fit into the very small space. Or, the sensor must be connected to the circuit with a relatively long cable. Parasitics of long connections can be large in comparison to the measured sensor changes, which can be on the order of a picofarad or less. Moreover, as the distance between the sensor and converter lengthens, conversion methods that are sensitive to the connection capacitance or leakage current to ground will make accurate measurements increasingly difficult.
Sigma-Delta ADC A well-proven technology, sigma-delta has been used for years in high-performance (>18 bits) ADCs. Figure 2 shows the simplified architecture of an industry-standard single-chip sigma-delta ADC. The capacitors CIN and CREF are periodically switched to the voltage and reference inputs VIN and VREF, and they pump charge into the integrator CINT. The comparator checks the integrator output and controls the phase of the input switches to close the feedback loop, which balances the charges flowing through the voltage and reference path.
A stream of zeros and ones, which can be seen on the comparator output, varies with the charge needed for the loop balance. The charge is proportional to voltage and capacitance. And because the capacitors have fixed values, the density of zeros and ones represents the ratio between the input voltage (VIN) and the reference voltage (VREF). The digital filter then extracts the information carried by the time-domain pattern of zeros and ones to form the digital result.
This architecture inherently features superior performance for linearity and accuracy, but there's a tradeoff between resolution and speed (output data rate). When more zeros and ones are allowed to be processed in the digital filter, it takes longer to get the result but produces more stable bits on the output. Only system noise limits the converter resolution. And, the output data rate is limited by the maximum clock frequency that can be accommodated by the switches' speed, integrator's bandwidth, and comparator's settling time.
Look into the portfolio of available converters to glimpse typical sigma-delta ADC performance. There are no missing codes at 24 bits (relates to differential nonlinearity); greater than 18-bit resolution (peak-to-peak resolution, i.e., a noise-free, stable digital result); 4-ppm integral nonlinearity; and data rates from 10 Hz to 40 kHz.
Sigma-Delta Capacitance To Digital Converter (CDC) The standard sigma-delta ADC is implemented by switching on-chip fixed capacitors and balancing charge between a variable voltage input and a defined voltage-reference input. Well, if the charge is proportional to voltage and capacitance, why not use a fixed input voltage and vary the input capacitor instead?
The modified sigma-delta circuit is shown in Figure 3. The fixed input voltage can be understood as an excitation voltage. The variable capacitor, which is moved off-chip, can be a capacitive sensor. As a result, the output data will represent the ratio between the sensor capacitance and CREF.
This novel idea permits direct interfacing between the capacitive sensor and the sigma-delta converter, which brings inherent features such as high resolution, accuracy, and linearity. Other features related to this circuit architecture are realized when interfacing capacitive sensors in the real world:
The interface isn't sensitive to capacitance between the sensor nodes and ground or leakage currents to ground, both up to defined limits based on a practical circuit implementation.
The complete capacitance-to-digital converter can be realized on one silicon chip, resulting in high integration, easy system implementation, high repeatability, high reliability, and last but not least, significantly lower system cost.
Please refresh the page if you have trouble reading this text.
Search Electronic Design
Email Newsletter
Sponsored By:
Electronic Design UPDATE provides readers with late-breaking news, opinions from industry experts, and timely technology stories. It's a unique opportunity to get your product message in front of engineers, engineering managers, and corporate managers while they're reading about critical information online.
Reprints
