Electronic Design

  
Reprints     Printer-Friendly    Email this Article    RSS        Font Size     What's This?


[Ideas For Design]
Design A Differential Voltage-Controlled Current Source

Jivesh Govil  |   ED Online ID #11878  |   January 19, 2006


Demand for voltage-controlled current sources (VCCSs) and multipliers in a wide spectrum of electronics and communication devices always seems to exist. The multipliers employed in circuits like the Gilbert Cell, however, produce outputs proportional to the product of two voltages. Research, as well as commercial applications, perpetually confronts the problem of implementing a single-ended multiplier with an output that's produced from the differences of two pairs of voltages. The circuit that's described below offers a simple and inexpensive solution.

To realize a differential VCCS (DVCCS), one must consider its design elements, which can be traced from the linear voltage-controlled resistor (VCR). The simplified circuit in Figure 1 shows a linear VCR, whose value can be either positive or negative depending on VG1 and VG2 applied to the gates of the MOSFETs. Assuming identical MOSFETs, the equivalent resistance (REQ) at the input (V1) is:

REQ = V1/i1 = [K(VG1-VG2)]-1 (1)

where K = µsCOX(W/L). W/L is the aspect ratio, µs is the electron mobility, and COX is the gate oxide capacitance. These results were obtained using the ID-VDS relationship in the triode region.

Equation 1 shows the equivalent resistance as the difference of two voltages. This can be exploited to implement a DVCCS. By ungrounding the two MOSFETs and interchanging M2 and CCII(+), and by making small modifications/additions, we obtain a new circuit—a DVCCS, or a two-quadrant multiplier.

Figure 2 shows the circuit realized as suggested above in design basics. The circuit consists of two MOSFETs and two current conveyors: CCII(+) and CCI(-). The currents iD1 and iD2 in the triode operating region of the MOSFET are:

iD1 = K [(V4− V2− VTH)− ((V1− V2)/2)](V1− V2) (2)

iD2 = K [(V3− V2− VTH)− ((V1− V2)/2)](V1− V2) (3)

Also, the currents i2 and i0 (assuming an ideal current conveyor; that is, IX = IZ, IX = IY, VX = VY, for CCI(+), and IX = −IZ, IX = IY, VX = VY, for CCI(−)) are:

i2 = iD2− iD1 (4)

i0 = −i2 (5)

Performing a complete mathematical analysis using Equations 2 through 5, we get the current at the output terminal as:

i0= K[(V1−V2)(V3 −V4)] (6)

Any three of the four voltages may be kept constant, and current may be obtained in proportion to the fourth one. Consequently, a conventional VCCS is realized. If all four voltages are varying, we obtain a differential VCCS. That is, the output current is proportional to the difference of two voltages and another two voltages.

Moreover, the DVCCS also can be visualized as a two-quadrant multiplier where the product of two voltages yields a proportionate current. Because V3 and V4 are applied to the gate terminals of the MOSFETs, they must always be positive. Furthermore, the direction of the current may be controlled by varying different voltages.

The circuit makes the most out of the MOSFET's beneficial characteristics—low power consumption, high input impedance, low fabrication cost by increasing cell density—with complete elimination of nonlinear square properties. As a result, the DVCCS rightly falls into the category of externally linear, internally nonlinear (ELIN) circuits.

Figure 2 shows how all voltages see a high input impedance. Also, with the current available at the Z terminal of the current conveyor, the current output is available from a low impedance source. This clearly shows that the realized VCCS is similar in characteristics to an ideal VCCS.

This circuit was simulated using Electronics Workbench (MultiSim). Its characteristics were verified using PSpice, which confirmed the expected voltage-current linearity.

To the author's best knowledge, no commercially available IC performs conversion of a differential voltage to a single-ended current. Implemented as an IC, this circuit would require only seven terminals: four voltage inputs, one current output, and two power-supply terminals.

The differential VCCS may find applications in AGC amplifiers, amplitude modulators, double-sideband modulators and detectors, single-sideband modulators and detectors, AM detectors, frequency doublers, squaring circuits, dividers, square-root circuits, rms measuring circuits, microemissive displays, temperature controllers, remote error sensors, and so on.

Acknowledgments: The author pays special thanks to Professor Raj Senani, Analog Signal Processing Research Lab., Netaji Subhas Institute of Technology (NSIT), New Delhi, India, for providing valuable suggestions in the classroom.


Reprints   Printer-Friendly  Email this Article  RSS    Font Size   What's This?


  • A New Design Inflection Point
  • Forecasting Industry Growth For 2009 And Beyond
  • EDA Retools To Exploit Multicore Architectures
  • Design And Verification Move Up In Abstraction
  • EDA Retools To Exploit Multicore Architectures
  • A New Design Inflection Point
  • Design And Verification Move Up In Abstraction
  • Challenges Lurk For 22-nm Physical Implementation
    1) 1-A Switching Regulators Operate With 96% Efficiency To Replace Linear Regulators
    (506 views today)
    2) Battery Pack Improves Li-Ion Management For Electric Vehicles
    (303 views today)
    3) Build A Smart Battery Charger Using A Single-Transistor Circuit
    (301 views today)
    4) New Power Approaches May Fuel Analog Job Opportunities In Security And Health Applications
    (298 views today)
    5) Step-Down Switching Regulator Provides 60-V Input Transient Protection
    (151 views today)
    ALL TOP 20



    Reader Comments

    Not bad for an initial design-exploit of current conveyors. But where do you buy those? This seems reminiscent of the gyrator circuits that were going to eliminate big heavy inductors in favor of tiny capacitors. Looks real good on paper, but not many in the field using real parts. There is a lot of buzz on current conveyors so maybe they will become real parts "real soon now." Meanwhile, four-quadrant, differential voltage input, voltage output, analog multipliers are available. See Analog Devices AD633 for example. Need a current output for some reason? Voltage-to-current converter circuits, using real parts, in a range of accuracies abound.

    Howard B. Evans, Jr. -September 28, 2006   (Article Rating: )

    i need a voltage controller circuit for varing AC voltage source to make the terminal voltage constant. I am doing my project so please sent me your ideas as soon as possible.

    Rajasudhan -March 21, 2006

    Where are the simulation results ?? What about the non-ideal behaviour of Current Conveyor ? Where are the details of power consumption and other specifications as area required etc ? These details should also be mentioned to make it worth fabricating

    Anonymous -February 06, 2006   (Article Rating: )

    What are ELIN? Anyways the design is explained well.

    John Master -January 26, 2006   (Article Rating: )

    Its a really excellent approach and has various applications.

    Abhinav Mehta -January 25, 2006

    Superb!

    Anonymous -January 23, 2006   (Article Rating: )

    The article was very knowledgeable and impressive. By using this, I found it's novel approach having practical applications. The editor deserves compliment for publishing such type of knowledgeable articles.

    Rabin K. Kim -January 21, 2006   (Article Rating: )

    Differential VCCS is I think presented in a very smart way. However, for clarity equation 1 must also be derived.

    Robert Lafate -January 21, 2006   (Article Rating: )

    Good Job!

    Anonymous -January 21, 2006   (Article Rating: )

    Your articles are highly impressive.

    Jivika -January 20, 2006   (Article Rating: )

    Hardcore designs like these should have little more detailed discussions.

    Tony Barter -January 20, 2006   (Article Rating: )

    I appreciate the novelty of the idea.

    Anonymous -January 20, 2006

    Great! The circuit has many applications. I find it interesting.

    Malind Bajaj -January 20, 2006   (Article Rating: )

    I don't get it. How can I apply this unless I'm an IC manufacturer ? There is no practical example, no sample application, and no test of an actual circuit. Simulation is NOT enough... transistor matching is perfect etc. Works on paper, maybe... but "Where's the Beef" ???

    H.Bissell -January 19, 2006   (Article Rating: )

    The article is highly application-oriented and seems to have great insight.

    MANISH JINDGAR -January 19, 2006   (Article Rating: )

    A very simple novel approach to realize differential voltage controlled current source.

    D. Albert -January 18, 2006   (Article Rating: )

    A very simple novel approach to realize differential voltage controlled current source.

    D. Albert -January 18, 2006   (Article Rating: )

    A very simple novel approach to realize differential voltage controlled current source.

    D. Albert -January 18, 2006   (Article Rating: )

    POST YOUR COMMENTS HERE
    Name:

    Email:
    Your Comments:

    Enter the text from the image below


    Please refresh the page if you have trouble reading this text.

    Search Electronic Design
         
      
     
    Email Newsletter
    Sponsored By:
    The Find Power Products monthly newsletter brings you the most important new developments within the world of power design. The newsletter includes exerpts from industry leader Sam Davis's exclusive blog, as well as overviews of the latest new products.

    Enter Email to Subscribe
      
    Web Seminar
    Sponsored By:
    Title: Exploring How Good GUIs Drive Adoption in the Digital Power Management Space
    Speakers: Don Tuite Deepak Savadaatt
    Date: 10/24/07
    Register: 

    Electronic Design Europe Electronic Design China EEPN Power Electronics Auto Electronics Microwaves & RF
    Mobile Dev & Design Schematics Find Power Products Military Electronics EE Events Related Resources