Included among the many applications for pulse-width modulation (PWM) are voltage regulation, power-level control, and fan-speed control. A PWM circuit for such systems can be implemented with three op amps on a single quad-op-amp chip (Fig. 1).

Because op amps are used for the modulator, it's suited for a wide variety of applications. For example, low-power op amps can be used in a low-power system, and high-frequency op amps can be used for a high-frequency PWM. The circuit in Figure 1 also generates a triangular wave.

The circuit consists of a triangular-wave generator (U1a and U1b) and a comparator (U1c). U1a is configured as an integrator (or de-integrator) and U1b as a comparator with hysteresis. At power-up, the comparator's output voltage is assumed to be zero.

U1a's noninverting input is biased at V_CC/2. A virtual connection between the inverting and noninverting inputs allows a constant current through R equal to I = V_CC/2R, which charges capacitor C. Thus, the U1A integrator output increases linearly with time. When it reaches 0.75 V_CC, the comparator output (U1b) changes to its maximum output voltage (V_CC). At that point, the integrator begins to de-integrate, causing the output voltage to decrease linearly. When it reaches 0.25 V_CC, the comparator output voltage changes to zero, and the cycle repeats. Thus, the integrator output is a triangular wave that swings between the levels of 0.25 V_CC and 0.75 V_CC.

U1c compares the triangular wave against the dc level V_IN. Its output is a square wave, with a duty cycle that varies from 0 to 100% as V_IN varies from 0.25 V_CC to 0.75 V_CC (Fig. 2). Frequency is determined by R, C, R1, and R2:

f = R2/(4RCR1)

where R2 > R1.

The ratio of R2 and R1 affects the operating frequency and the amplitude of the triangular wave. Given that V_TH is the triangular wave's maximum voltage and V_TL is its minimum voltage, the amplitude swing is:

V_TH = V_CC(R1 + R2)/2R2, and

V_TL = V_CC(R2 − R1)/2R2,

where R2 > R1. Therefore:

V_TH − V_TL = (R1/R2)V_CC (R2 > R1).

The triangular wave's peak-to-peak voltage is centered at the V_CC/2 bias voltage generated by R3 and R4. With the circuit configuration shown, the PWM operates on a single supply. Use micropower op amps and larger resistors (R and R1 to R4) for low-power applications and high-frequency op amps for higher-frequency applications. (The quad op amp shown comes in a single package.)

Reprints

Printer-Friendly

Email this Article

RSS

Submit PlanetEE del.icio.us Digg Reddit Newsvine StumbleUpon Netscape Yahoo MyWeb Live Bookmarks Fark  Submit

Font Size

What's This?

MLCCs Stand Up To ESD Quad-Output Controller Trims Parts Count Video Filter/Buffers Boost Performance And Integration 45W Supplies Power Electrostatic Air And Oil Cleaner Devices Desktop HDD Packs 500 GB Per Disk 1A Switching Regulators Perform As High-Efficiency Replacements

A New Design Inflection Point Forecasting Industry Growth For 2009 And Beyond EDA Retools To Exploit Multicore Architectures Design And Verification Move Up In Abstraction EDA Retools To Exploit Multicore Architectures A New Design Inflection Point Design And Verification Move Up In Abstraction Challenges Lurk For 22-nm Physical Implementation

1) Transportation Guidelines For Lithium Batteries Get Updated (828 views today) 2) Build A Smart Battery Charger Using A Single-Transistor Circuit (255 views today) 3) 1-A Switching Regulators Operate With 96% Efficiency To Replace Linear Regulators (160 views today) 4) WHITE PAPER: Liquid-Level Monitoring Using a Pressure Sensor (114 views today) 5) 2008 BEST Electronic Design Winners (108 views today) ALL TOP 20

Reader Comments it would be nice if u can explain with more waveforms and with more generic approach........ ........ arun -November 21, 2006   (Article Rating: ) excellent Dibyajyoti Bose -October 26, 2006   (Article Rating: ) I designed a similar circuit a few days back, using the TL084 as the quad OP-AMP. My supply voltage was 12 volts dc. I got a pure triangular wave with amplitude swing of about 9.5 volts peak to peak. I adjusted component values just to see the frequency response. The triangular wave was good up to 85kHz. It was distorted thereafter. Kindly suggest a different quad op-amp whose triangular wave can remain good at 400kHz. JOHN IKEDE -August 31, 2005   (Article Rating: ) better than my university lecturer - dr w b barry w -May 09, 2005   (Article Rating: ) I need to vary the duty cycle. NB: frequency must be constant. I am looking forward to trying the design I saw on this article. Bendzii -March 29, 2005   (Article Rating: ) Extreme versatility. Metodi Chalapoutov -January 01, 2005 ineed avariable duty cycle.diffrent duty cycle in the same period ghaith fandi -December 16, 2004 really good srilan maranan -September 15, 2004 I was looking for a 0% - 100% Analog (NON-COMPUTER) PWM circuit and this one just dropped in my lap. I have not constructed, it but I look forward to using it. When controlling current in applications where getting approval for a microcontroller's operation can be difficult, a purely HARDWARE design can come in handy. The fact that it ranges from 0% (completely off) to 100% (fully on) is the best feature of this design. Steven Alexander -March 08, 2004
POST YOUR COMMENTS HERE Name: Email:
Your Comments: Enter the text from the image below Please refresh the page if you have trouble reading this text.