[Engineering Feature]
Bright Outlook For Solar Power Cogeneration
A revolution is under way as new solar generation systems pump excess energy back into the power grid.
Solar power, specifically the kind that runs lights and television sets and keeps the milk in the refrigerator cold, has undergone a resurgence in the U.S. since 2000. That's when the IEEE released a standard—IEEE 929-2000, Recommended Practice for Utility Interface of Photovoltaic (PV) Systems—covering the design of dc-ac inverters for systems connecting PV systems to the utility grid.
Prior to that date, even if they wanted to allow homeowners and businesses to connect to the grid, the utilities had to certify each installation individually for safety and compliance with power standards. Consequently, U.S. solar power claimed a sort of outlaw status. Most installations were off the grid, charging battery banks that supported 12-V lighting and appliances.
The off-the-grid/battery model wasn't just limited to remote farmsteads, vacation cabins, cruising sailboats, and RVs, though. According to Dan Magni, director of engineering at RWE Schott Solar, which designs and implements large solar projects, most of the company's work on off-the-grid projects with battery backup (mostly in the government sector) ended a few years ago. The last two years have seen an "explosion" of grid-tied business in the private sector. (The company's largest grid-tied project to date is a 300-kW system for the Cache Creek Indian Casino in Yolo County, Calif.) Magni's observations are echoed by Clifford B. Schrock, whose company, Solar/Wind Power of Portland, Ore., designs small residential systems in the Pacific Northwest.
MAKE HAY WHILE THE SUN SHINES There's a completely different mindset behind these new installations. The people who purchase the systems have an incentive to reduce their electric bills through net-metering. Essentially, their electric meters turn backward some of the time.
At that point, the economics get interesting. It's true that the home or business owner may be putting extra power minute by minute onto the grid, which the meter is recording. Yet at the end of a billing cycle, the home or business probably has used more energy than it has created. That means for most installations the model is more like using the grid in lieu of a battery bank, rather than being a profit-making venture. If one does manage to put net positive energy into the grid, the utility will pay for it—but not at its regular billing rates. (See "Entrepreneuring in Solar Power Generation," p. 48).
Because this means the utility is selling less of the commodity it is in business to sell, what economic incentive does it have to let customers connect solar systems to its meters? Ignoring political pressures, there wouldn't be any incentive if electrical demand were constant over the course of a day or if it were easy to add surplus generating capacity to meet peak demand. Yet demand does vary, summer brownouts are becoming too common, and it isn't easy to get permits to build new power plants. Solar installations supply extra generating capacity for the utilities precisely when most necessary without requiring them to build new plants. Add political pressures back into the equation and it's not hard to understand why utilities now tolerate and even encourage customers to hook up Underwriters Laboratories-approved, properly installed grid-tied solar systems.
There's another reason why utilities don't discourage solar power. According to RWE Schott senior field engineer Mike McGoney, the buzz in the power-generating community is that natural gas prices will continue to be volatile, with an upward trend. Thus, the more experience the utilities can get with all forms of unconventional generation, the better.
Note that the design standards discussed in this article relate to grid-tied solar power in the U.S. (Other important standards are described in "A Convocation of Standards" at www.elecdesign.com, Drill Deeper 9323.) But solar power is a global phenomenon, and demand in the U.S. is considerably less than it is in other places. For instance, because demand in Germany is so great, suppliers are rushing to increase capacity to feed a Central European market that's estimated to be installing 1 MW of solar capacity every day. But a discussion of worldwide standards is fodder for another article.
BATTERIES NOT INCLUDED Grid-tie systems have no batteries, which reduces system cost and complexity. Cost is significantly less without batteries, and with no need for battery-charging circuitry, grid-tie inverters are comparatively simple. In fact, the whole system is simple from an installation standpoint (Fig. 1).
Other than safety disconnects, mounting structure, and wiring, solar modules and a grid-tie inverter are all that's involved in a grid-tie system. Inverters actually integrate three functions: converting the dc from the modules to ac and synchronizing it with the utility; tracking the maximum power point of the modules to operate the system at peak efficiency; and disconnecting the PV system from the grid if power from the utility is interrupted.
SOLAR-CELL TECHNOLOGY Daryl Chapin, Calvin Fuller, and Gerald Pearson developed the first practical solar cell at Bell Laboratories in 1953. It was 2.5 cm2 of crystalline silicon with a conversion efficiency of about 6%.
Cell efficiency determines how well solar power works in terms of economics. Irradiance, the sun's power available at the surface of the earth, peaks at about 1000 W/m2. Insolation is the energy that's actually available at any location. The map in Figure 2 depicts average insolation for the U.S.
Efficiency numbers for conventional crystalline-silicon cells are about 15% to 20%. In the commercial arena, BP Solar recently claimed the world's record for efficiency in 125-mm diameter cells at 18.3%. Kyocera claims 14% efficiencies for its cells.
Higher efficiencies are possible—in the lab and in applications where price is no object. In mid-2003, Boeing's Spectrolab subsidiary said the latest terrestrial versions of its Improved Triple-Junction (GaInP2/GaAs/Ge) space solar cells could convert at 36.9% efficiency. Each of the cells' three layers captures and converts a different portion of the solar spectrum.
These are high efficiencies. But obviously, three layers of III-V semiconductor built on a metal-organic CVD manufacturing process doesn't lead to a low-cost product.
Emcore Photovoltaics, which acquired Tecstar's PV division, also produces triple-junction PV cells for space applications. But it hasn't claimed efficiencies quite as high as Spectrolab.
A recent collaboration between the University of California at Berkeley, Cornell University, and Lawrence Berkeley National Laboratory observed that the bandgap energy of InN is approximately 0.7 eV at room temperature. Earlier work had reported a lower value. The significance of the discovery, if correct, is that multijunction PV cells fabricated of InN and GaN to form InGaN ternary alloys would have bandgaps of 0.7 to 3.4 eV. This would cover the entire solar spectrum and provide 50% to 70% conversion efficiencies. Fortunately, InGaN alloys are said to tolerate relatively large lattice mismatches, so manufacturing could be cost-effective, even given the exotic materials.
More in line with emulating Mother Nature, MIT's Shuguang Zhang and collaborators are exploring cells that use spinach to convert light into an electrical charge (see "Spinach-Powered Portables Take 'Green' To A New Level," electronic design, Oct. 18, 2004, p. 8). They integrated a protein complex derived from spinach chloroplasts with organic semiconductors to make solar cells that are thinner and lighter than conventional cells. But Zhang cautions that the peptides currently keep the protein complex stable for about three weeks, and the cells convert only 12% of light to electrical charge.
The alternative to crystalline-silicon cells is amorphous silicon (a-Si). It can be produced in a continuous-sheet manufacturing process, making it potentially much more economical than wafer-grown cells. The drawbacks are lower efficiency and, at this time, only modest manufacturing capacity.
Uni-Solar's a-Si panels employ a tri-layer technology like Spectrolab's (Fig. 3). The process is described in a 1997 Photovoltaic Specialists Conference paper titled "Triple-Junction Amorphous Silicon Alloy PV Manufacturing Plant of 5 MW Annual Capacity," which can be found at www.physics.utoledo.edu/~dengx/papers/guha97d.pdf.
The paper cites 7.5% efficiency, but the company later said it improved that figure by 30%. In looking at these cells for space applications, the NASA Lewis Center measured a 12% beginning-of-life conversion efficiency.
Efficiency, however, isn't the end of the story. Because Uni-Solar's manufacturing process is based on materials deposited on a continuous web, production costs are lower than wafer-based processes. If space isn't an issue, low cost becomes very attractive. Previously, Uni-Solar's production capacity was limited to 5 MW per year. But a new manufacturing facility with six times the capacity, which is bound to introduce economies of scale, is now online.
I'm curious about the term "cogeneration". I read the artile because I understood cogeneration to mean that another form or energy was produced in addition to the electical current. For example a natural gas burning generator may need to be cooled with water to operate efficiently. The resulting hot water could then be used to heat water for use via a heat exchanger.
Bill -September 09, 2005
Great article. The interesting aspect is that there is a simple break even point where you would be an idiot for NOT putting solar cells on a new home since you could likely role the cost into your mortgage. The additional amount of money you pay per month in your 15-30 year mortgage would be less than if you would have to pay for the KW-h. In simpliest terms do you want to pay $1000 per month on your mortgage with a $200 energy bill or $1080 per month with a $100 energy bill? (plus you can deduct the interest of your motgage off your taxes.)
I don't think that break-even point has happened yet but when it does, it will be a simple decision.
Anonymous -March 06, 2005 (Article Rating: )
I would suggest that PV-based power systems' viability has little to do with materials or power electronics. Look instead at whose vested interests are served or threatened, the flow of capital and realpolitik, and which companies like BP Solar are hedging their bets by adding solar to their petrolium business.
EEs with a little extra cash might consider investing in solar-tech and materials companies like Evergreen Solar and MEMC Electronic Materials.
Are there any information/issues with the Solar cells desgined as semi-transparent film on glass which replace a normal window (or ultimately are glued to a normal window)? I beleive that RWESchott in Germany has made the product. Any pilot/trail information would be appreciated.
D. khomarlou -January 28, 2005
PLease give us more information on this topic. I believe photovoltaic is finally coming of age!!
Keith Volz -December 29, 2004
About InGaN PVs, your article mentions: "Earlier work had reported a lower value [compared to 0.7 eV]." Actually, the InN energy-gap was thought to be higher (1.9 eV) but had been realized to be 0.7 eV, a short time ago, allowing for the InGaN alloy system to span almost the entire solar spectrum (3.4 to 0.7 eV). It's a matter of "who" and "when" this material will achieve 500 W/meter<sup>2 </sup>at below $1/W. The Materials Science profession has a large role to play in addressing global warming and reducing America's dependence on costly foreign oil sources....
Trebor Jorgenson -December 23, 2004
I am really glad to see that you writing about the progress of renewable energy sources. I hope that you will write more articles about this in the near future. The EE profession has a large role to play in addressing global warming and reducing America's dependence on costly foreign oil sources.
David Van Winkle -December 21, 2004
Great Article
David Schenck -December 21, 2004
An Excellent high level article covering the state of solar technology.
Laurence Dunn -December 20, 2004
Your Comments:
Enter the text from the image below
Please refresh the page if you have trouble reading this text.
Search Electronic Design
Email Newsletter
Sponsored By:
The Find Power Products monthly newsletter brings you the most important new developments within the world of power design. The newsletter includes exerpts from industry leader Sam Davis's exclusive blog, as well as overviews of the latest new products.
Enter Email to Subscribe
Web Seminar
Sponsored By:
Title: Exploring How Good GUIs Drive Adoption in the Digital Power Management Space
Reprints
)
)
