Image

Use Noise Spectral Density to Evaluate ADCs in “Software-Defined” Systems

July 28, 2015
Noise spectral density (NSD) and its distribution over the band of interest can provide insight and guide the converter-selection process.

The expanded availability of high-speed and very-high-speed ADCs and digital processing is making oversampling a practical architectural approach for broadband and RF systems. Semiconductor scaling has done much to boost speeds and lower costs (in dollars, power, board areas, etc.), enabling system designers to explore different avenues of converting and processing signals either using broadband converters with flat noise spectral density, or band-limited delta-sigma converters with high dynamic range in the desired band of interest. These techniques change the way design engineers should think about signal processing, and the way they specify products.

Download this article in .PDF format
This file type includes high resolution graphics and schematics when applicable.

In comparing systems that operate at very different speeds, or looking at how a “software-defined” system will handle signals of different bandwidths, noise spectral density (NSD) can be considerably more useful than signal-to-noise-ratio (SNR) specifications when making comparisons. It doesn’t replace the other specifications, but is a useful item to add to one’s analysis toolbox

How Much Noise is in My “Band of Interest?”

 When SNR is specified on a data converter’s datasheet, it indicates power in a full-scale signal compared to the total noise power present in all the other frequency “bins.”

1. Processing gain makes it possible to “retain” all of the signal while “throwing away” 7/8 of the noise.

Now consider a simplified case for comparing SNR to NSD (Fig. 1). Assume the ADC is being clocked at 75 MHz. The display in the figure, which is running a fast Fourier transform (FFT) on the output data, shows a spectrum from dc to 37.5 MHz. In this example, the “signal of interest” is the only strong signal present, and it happens to be located at around 2 MHz. For “white” noise (which includes quantization and thermal noise in most situations), the noise is evenly spread across the Nyquist band of the converter. In this case, it’s from dc to 37.5 MHz. 

Since the signal of interest is between dc and 4 MHz, it’s relatively simple to apply digital post-processing to filter out, or “throw away,” everything above 4 MHz (keeping only what is in the red box).  Here, that would entail throwing away 7/8 of the noise and keeping all of the signal energy—essentially improving effective SNR by 9 dB. Stated another way, if it’s known that the signal is going to be in one half of the band, one can, in effect, “throw away” the other half of the band while eliminating only noise. 

This leads to a useful rule of thumb: Processing gain can provide an extra 3 dB/octave of SNR for oversampled signals in the presence of “white” noise.  In the Figure 1 example, it was possible to apply this technique across 3 octaves (a factor of 8) and thus realize 9 dB of SNR improvement. 

Of course, if the signal is going to be somewhere between dc and 4 MHz, it isn’t necessary to use a fast 75-Msample/s ADC to capture the signal. A mere 9 or 10 Msamples/s would meet the Nyquist sampling theorem bandwidth requirements. In fact, it’s possible to decimate the 75-Msample/s sample data by a factor of 8 to produce an effective 9.375-Msample/s data rate, while preserving the noise floor in the band of interest.  

It is important to perform the decimation properly. Decimating by simply throwing away 7 out of every 8 samples would cause the noise to “fold back,” or alias, into the band of interest. In that case, there would be no SNR improvement. It’s necessary to filter first, and then decimate, to realize the processing gain.

Even in that case, while a perfect “brick wall” filter would eliminate all of the noise and yield the ideal 3 dB/octave of processing gain, no actual filter has that kind of characteristic. In practice, the amount of filter stopband rejection necessary is a function of how much processing gain is to be achieved.  Also, keep in mind that the “3 dB/octave” rule of thumb is based on an assumption that the noise is “white.” It’s a reasonable assumption in many, but not all, cases.  

One important exception crops up when the dynamic range is limited by nonlinearity or other sources of spurious intermodulation products in the passband. In these cases, the “filter and throw-away” approach may or may not catch the performance-limiting spur, and more careful frequency planning approaches may be required.   

Converting SNR, Sample Rate into Noise Spectral Density

When more than one signal is present in the spectrum, such as in the FM broadcast band with its myriad  radio stations, the situation gets more complicated.  In terms of recovering any one signal, what’s most important is not the overall noise of the data converter, but rather the amount of converter noise that falls into the “band of interest.” This requires digital filtering and post processing to eliminate all of the out-of-band noise. 

Multiple paths can be taken to reduce the amount of noise that falls into the red box.  One way is to select an ADC with a better SNR (less noise).  Alternatively, using an ADC with the same SNR and a faster clock (e.g., 150 MHz) will “spread” the noise over a broader bandwidth, leaving less noise in the red box.

NSD Enters the Picture

This raises a new question: Is there a better specification than SNR for quickly comparing converters to determine performance “in the red box?”

This is where noise spectral density enters the picture. By specifying noise in terms of “spectral density” (typically in dB relative to full scale per hertz of bandwidth (dBFS/Hz), it’s possible to compare different ADCs with different sampling rates to determine which might have the lowest noise in a particular application.

Table 1 below represents a data converter with 70 dB of SNR. It illustrates the improvement in NSD with sample rates from 100 MHz to 2 GHz.

Table 2 below shows several combinations of SNR and sampling rates for some very different converters. However, all have the same NSD, so that each would have the same total noise across a 1-MHz channel. Bear in mind, the actual resolution of the converter may be a much larger number than the “effective number of bits”—many converters want to have extra resolution to ensure that the quantization noise has negligible contribution to the NSD.

In a conventional single-carrier system, it might seem absurd to use a 10-Gsample/s converter to capture a 1-MHz signal. But in a multi-carrier “software-defined” environment, that may the exact course of action taken by a designer. One example might be a cable set-top box, which may use a 2.7- to 3-Gsample/s “full spectrum tuner” to capture the cable signal that’s composed of hundreds of TV channels, each with a few megahertz of bandwidth.  For data converters, noise spectral density is conventionally specified in units of dBFS/Hz. (That is, dB with respect to full scale per hertz, a relative measure). This provides a sort of “output referred” measurement of the noise level—or, alternatively in dBm/Hz (dB-milliwatts/Hz), or even dBmV/Hz (dB-millivolts/Hz), to provide a more absolute measurement, i.e., “input referred” indication of the data converter’s noise. 

SNR, full-scale voltage, input impedance, and Nyquist bandwidth can also be used to calculate an effective noise figure for an ADC. However, that’s a fairly involved calculation (see Analog Devices’ MT-006 tutorial: “ADC Noise Figure—An Often Misunderstood and Misinterpreted Specification”). 

Oversampling Alternatives

Running an ADC at higher sample rates generally means higher power consumption, both in the ADC itself and in the subsequent digital processing.  Table 1 illustrates the benefits of oversampling in terms of NSD, but the question remains: “Is oversampling really worth it?”

As Table 2 shows, it would also be possible to achieve better NSD by using a lower-noise converter.  A system that needs to capture multiple carriers would need to be running at a higher sample rate, so each carrier was oversampled. Nonetheless, oversampling still has a number of benefits:

Simplification of the anti-alias filtering—the act of sampling will “alias” higher-frequency signals (and noise) back down into the Nyquist band of the converter. Thus, to avoid aliasing artifacts, these signals must be suppressed by a filter ahead of of the ADC.  This means that the filter’s transition band must fall between the highest desired capture frequency (Fin) and the alias of that frequency (Fsample-Fin).  As Fin approaches one half of Fsample, the transition band of this anti-alias filter becomes very narrow, requiring a very high-order filter. Oversampling by 2-to-4 substantially relieves this constraint in the analog domain, placing the onus on the relatively easier-to-process digital domain.

Minimizing the impact of folding converter distortion products—even with a perfect anti-alias filter, imperfections in the ADC will generate spurs and other distortion products, including some very high-order harmonics.  These harmonics will also “fold” across the sampling frequency—potentially falling back “in band” and limiting SNR in the band of interest.  At higher sample rates, the desired band becomes a small fraction of the Nyquist bandwidth, and therefore reduces the folding occurrences. (It’s also worth mentioning that oversampling also aids in the frequency planning for other system spurs that might fold in-band, such as device-clock sources.)

Processing gain affects any “white” noise— this includes thermal and quantization noise, along with noise from certain types of clock jitter.

As higher converter and digital-processing speeds become more readily available, system designers are more frequently using some amount of oversampling to leverage these advantages.

“Noise Floors” and FFTs

2. Changing the FFT size changes the appearance of the “floor” in a spectral plot. The plot on left has a sample size of 8,192 and the plot on the right has a sample size of 524,288. Note the SNRFS is about 74.8 dB for both plots. (Click for larger image.)

It’s tempting to compare converters by inspecting spectral plots and looking at the depth of the noise floor (Fig. 2). When making such comparisons, it’s important to remember that the plotting of the spectrum depends on the size of the fast Fourier transform (FFT). Larger FFTs will break the bandwidth into more “bins,” accumulating less noise in each bin. In that case, the spectral plot will apparently show a “lower noise floor,” but this is just a plotting artifact. In fact, the noise spectral density has not changed (this would be the signal-processing equivalent of changing the resolution bandwidth of a spectrum analyzer).  

In the end, “floor” comparisons would be acceptable if the sampling rates and FFT sizes were identical (or scaled appropriately). If not, it could be misleading. This is where the NSD specification provides a useful direct comparison. 

When the Noise Floor Isn’t “Flat”

So far, these discussions of processing gain and oversampling have been based on the assumption that any noise is “flat” across the Nyquist band of the converter.  That is a reasonable approximation in many cases, but a number of situations arise where that assumption doesn’t hold up.

For example, it has already been mentioned that processing gain doesn’t really apply to spurs (though oversampled systems may offer some advantages in frequency planning and handling spurs). Besides that, 1/f noise and some types of oscillator phase noise will have spectral “shaping,” and processing gain calculations will not apply in such cases.

3. For “shaped” noise, the gain from discarding the out-of-band noise can be much greater than that in Figure 1, and in fact, sigma delta modulators routinely realize processing gains of 9-to-15 dB/octave or more for the portion of the noise that is shaped by the modulator. (Not all noise sources in the system are shaped by the modulator feedback).

One important circumstance in which noise is not flat occurs with the use of sigma-delta converters. Sigma-delta modulators use feedback around the quantizer to “shape” the quantization noise of the modulator, thus lowering the noise that falls into a “band of interest” at the expense of raising the noise out of band (Fig. 3).

Even without a full analysis, one can see that using NSD as the specification to determine the in-band usable dynamic range is particularly helpful for sigma-delta modulators. Figure 4 shows a “zoomed in” plot of the noise floor for a high-speed, bandpass, sigma-delta ADC. Across the 75-MHz band of interest (with center frequency at 225 MHz), the noise is around –160 dBFS/Hz, providing more than 74 dBFS of SNR.

Download this article in .PDF format
This file type includes high resolution graphics and schematics when applicable.
About the Author

David Robertson | General Manager, High Speed Converter Group

David (“Dave”) Robertson is the General Manager of the High Speed Converter Group at Analog Devices. He holds 16 patents on converter and mixed-signal circuits, and has authored numerous technical papers and award-winning presentations for venues such as the ISSCC and the VLSI Symposium. He has a BA and BE from Dartmouth College, with dual majors in economics and electrical engineering.

About the Author

Gabriele Manganaro | Engineering Director, High Speed Converters

Gabriele Manganaro, Engineering Director for High Speed Converters at Analog Devices, has co-authored 60 scientific papers, three books, and holds 12 US patents. He is Senior Member of the IEEE and a Fellow of IET. He holds a Dr. Eng. and a PhD in Electronics from the University of Catania, Italy.

Sponsored Recommendations

Comments

To join the conversation, and become an exclusive member of Electronic Design, create an account today!